Improvement of saddles: How to avoid fast cracking strings?

Vintage, Modern, V & C Series, Signature & Special Editions

Moderators: rickenbrother, ajish4

Post Reply
User avatar
Hotzenplotz
Intermediate Member
Posts: 942
Joined: Sun Sep 26, 2010 8:51 am

Improvement of saddles: How to avoid fast cracking strings?

Post by Hotzenplotz »

It is always the same:

Using the TI JS110 flats (these are recommended here in the forum as long lasting) at first the high e-string cracks, a bit later the a-string.
All this happens after about 50 hours of playing time. I do not play "brutal". Sometimes very soft, sometimes in an "intensive strumming" way. No much bendings, too.

Now I thought about using fine sandpaper (400 or 800) for to smooth the edges a bit. Is this a good idea, if yes, how to do? What is the best way to solve that problem?
User avatar
electrofaro
Senior Member
Posts: 3611
Joined: Sun Apr 26, 2009 3:25 pm

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by electrofaro »

I only have the g-string snapping on me TI .011 flats, I checked the saddle, smoothed it, but no effect, so curious as to what the exact action to take is!
'67 Fender Coronado II CAB * '17 1963 ES-335 PB * currently rickless
User avatar
Hotzenplotz
Intermediate Member
Posts: 942
Joined: Sun Sep 26, 2010 8:51 am

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by Hotzenplotz »

How to smooth the saddles correctly without causing a buzz or muddy tone?
User avatar
jingle_jangle
RRF Moderator
Posts: 22679
Joined: Wed Dec 22, 2004 6:00 am
Contact:

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by jingle_jangle »

Clean up the "ramp" transition from the saddle groove to the flat of the saddle on the bridge side of the saddle. Don't mess with the other edges of the string groove.

I use #400 and then #600 paper to smooth this edge into a nice soft radius.
User avatar
iiipopes
Intermediate Member
Posts: 1428
Joined: Tue May 22, 2007 5:02 pm

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by iiipopes »

In addition to what Jingle Jangle said, after you smooth the saddle notch, some people take a used wound string of the same diameter and run it back and forth burnishing the slot. But you have to keep it perfectly straight to the backramp of the saddle, or you will round over the leading edge and ruin what you're trying to accomplish: smooth travel with precise "witness point" intonation.
User avatar
electrofaro
Senior Member
Posts: 3611
Joined: Sun Apr 26, 2009 3:25 pm

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by electrofaro »

What is the bridge side of the saddle? :?: :oops: Isn't the saddle the middle of the bridge? :?:
'67 Fender Coronado II CAB * '17 1963 ES-335 PB * currently rickless
User avatar
jingle_jangle
RRF Moderator
Posts: 22679
Joined: Wed Dec 22, 2004 6:00 am
Contact:

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by jingle_jangle »

I dunno--how would you describe the end of the saddles nearest the bottom/bridge end/lower strap peg of the bass?
User avatar
Hotzenplotz
Intermediate Member
Posts: 942
Joined: Sun Sep 26, 2010 8:51 am

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by Hotzenplotz »

Thanks so far! I think at first I have to look very close to the saddles with a loupe what You are talking about.

Are there some close-up photos of the corners I have to ply?

As far as I understood there is a small fin at the edge in the direction of the neck where the strings chafe themselves to death. And there is another angle in the middle (more or less) of the saddle that is very necessary for a good tone. Right?
User avatar
electrofaro
Senior Member
Posts: 3611
Joined: Sun Apr 26, 2009 3:25 pm

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by electrofaro »

jingle_jangle wrote:I dunno--how would you describe the end of the saddles nearest the bottom/bridge end/lower strap peg of the bass?
Well, the bottom of the bridge to me is the underside, the front the side that face the neck, the back the side that faces the tailpiece.

Link to 12-string saddles:
http://brawer.com/wordpress/wp-content/ ... c05767.jpg
'67 Fender Coronado II CAB * '17 1963 ES-335 PB * currently rickless
User avatar
Hotzenplotz
Intermediate Member
Posts: 942
Joined: Sun Sep 26, 2010 8:51 am

Re: Improvement of saddles: How to avoid fast cracking strings?

Post by Hotzenplotz »

Yesterday I noticed - and changed - that the bridge was raised at the side to the tailpiece some noticeable degrees.

Could this have been the reason for cracking the strings very fast?

The concerning saddles I sanded carefully with fine sandpaper, too. Just to break the edges without loosing tone quality.
Did work.

Now I have to wait - and play it.
Post Reply

Return to “Rickenbacker Guitars: by John Simmons”