Page 1 of 1

1973 4000 bass in need of a re-fret

Posted: Fri Jul 26, 2019 6:38 pm
by LBx
Grabbed one off a friend who recently nabbed it from a co worker. Neck and radius are perfect and the thinness of the body is something I didn't know I needed 'til I played it. A lot more comfortable and solid than the bolt on Fender knock off I had prior. Couple questions though:

Would the neck be set or thru to the end of the body for this year? Not totally bothered if it's the former, just curious.

Fret board is original but it was converted to fretless way back :?. Do the Stew Mac sizes listed here for a '78 apply to '73 as well? The luthier recommended to me has a large collection of NOS parts on hand but a specific fret wire seems like kind it may be kind of an outlier. Would like to keep it as original as possible...

Re: 1973 4000 bass in need of a re-fret

Posted: Fri Jul 26, 2019 7:39 pm
by collin
I'd venture a statement that all 4000 models made in the 70s were set neck.

You'll know easily since the set neck models have a "step" from where the neck heel meets the body it's glued into, and also the "skunk stripe" from the neck wood won't continue through the rest of the body, at least on transparent finishes.

Those are cool basses, congrats.


EDIT: Yes, the stock fretwire you're looking for is Stew Mac #0148

Re: 1973 4000 bass in need of a re-fret

Posted: Fri Jul 26, 2019 8:36 pm
by LBx
This is the "step" you mentioned I take it?

Image

The jetglo doesn't cover a stripe that would otherwise be there I'm guessing? It's part of the build depending on the year & the wood used? Nice detail...

Re: 1973 4000 bass in need of a re-fret

Posted: Fri Jul 26, 2019 8:38 pm
by LBx
collin wrote:Yes, the stock fretwire you're looking for is Stew Mac #0148
Nice one. I'll pass that on if need be. Thx!

Re: 1973 4000 bass in need of a re-fret

Posted: Sat Jul 27, 2019 4:55 pm
by collin
LBx wrote:This is the "step" you mentioned I take it?

Image

The jetglo doesn't cover a stripe that would otherwise be there I'm guessing? It's part of the build depending on the year & the wood used? Nice detail...
Yep that’s the step, it’s a set neck.


The vast majority from that era are Fireglo, Mapleglo and sometimes Burgundyglo which are all transparent and show the skunk stripe (or lack thereof) unlike opaque finishes Jetglo or Azureglo

Re: 1973 4000 bass in need of a re-fret

Posted: Sat Jul 27, 2019 8:42 pm
by jps
Exhibit A:
Rick 4000 '75 FG 05.jpg
Exhibit B:
4000 '72 FG 02a.jpg

Re: 1973 4000 bass in need of a re-fret

Posted: Sat Dec 07, 2019 12:37 pm
by LBx
BOOM. Finished, finally...

Image

Someone "Fenderized" the fret board so that had to be fixed as well.

Bit of tail lift but the break angle is good.

I'm really into it...

Re: 1973 4000 bass in need of a re-fret

Posted: Sun Dec 08, 2019 7:33 pm
by jps
Which Tranor cab is that? I've had three Traynor cabs over the decades (one YT-15, and two YS-15s), but none were the "new fangled" ones with the bumpers.

I've, also, owned a couple of amps, A YBA-3, and a YSR-1. I should have kept the latter, it made for a wonderful recording amp.

Re: 1973 4000 bass in need of a re-fret

Posted: Mon Dec 09, 2019 7:29 pm
by LBx
It's a YS-15P. Front ported. A handful of bands I'm into and gear dorks on another forum were all about the Dietz & Mesa Thiele type stuff for a while so I snagged this as a version of that. Plenty of low end for my corner of the basement. Bass & guitar in C#. Should match the grill cloth though!

Re: 1973 4000 bass in need of a re-fret

Posted: Mon Jun 22, 2020 12:59 pm
by henry5
collin wrote:I'd venture a statement that all 4000 models made in the 70s were set neck.
I appreciate this is reviving an old thread, but I thought I’d correct this, which is inaccurate. 4000 models were through-neck until some time in ‘72. I had a ‘72 4000 that was a through-neck and have seen several others. My ‘73 4000 however was a set-neck.