Tremolo Arm Setup
Moderator: jingle_jangle
Tremolo Arm Setup
About a month ago I purchased a Mexican Fender Standard Stratocaster with a maple neck, in aged cherry sunburst. Several YouTube videos on whammy bar setup suggested setting the claw so that you can raise the pitch a full minor third on the G-string, a whole step on the B-string, and a half step on the high E. After taking some measures to make sure the guitar stayed in tune, my tech lifted the bridge enough so that I could raise and lower the pitch. However, I can only pull up a whole step on the G-string. If my intention is to emulate Hendrix and Jeff Beck, should I have the claw readjusted
- Killed_by_Death
- New member
- Posts: 7
- Joined: Tue May 17, 2016 9:52 am
vibrato arm
That arm is actually used for a vibrato effect.
Do the adjustments yourself. Here is Fender's own guide:
http://www2.fender.com/support/articles ... etup-guide
Do the adjustments yourself. Here is Fender's own guide:
http://www2.fender.com/support/articles ... etup-guide
"The pleasure is to play, makes no difference what you say."
Ian Fraser Kilmister (24 Dec 1945 – 28 Dec 2015)
Ian Fraser Kilmister (24 Dec 1945 – 28 Dec 2015)
Re: Tremolo Arm Setup
Vibratos are best for going down and somewhat up in pitch, Best used for divebombs. Bend the strings as you normally would to raise the pitch. The vibrato is limited in its upward motion by either the bridge plate making contact with the body or the block hitting the side of the cavity, either way, no adjustment of the claw with help either scenario; the claw is primarily for setting the height of the bridge plate off the body. Keep in mind that the height of the bridge plate will affect string height, too, so readjusting the saddles may be required.
Re: Tremolo Arm Setup
Thanks! Isn't it the case that the higher the bridge, the more you can raise the pitch with the tremolo arm?jps wrote:Vibratos are best for going down and somewhat up in pitch, Best used for divebombs. Bend the strings as you normally would to raise the pitch. The vibrato is limited in its upward motion by either the bridge plate making contact with the body or the block hitting the side of the cavity, either way, no adjustment of the claw with help either scenario; the claw is primarily for setting the height of the bridge plate off the body. Keep in mind that the height of the bridge plate will affect string height, too, so readjusting the saddles may be required.
https://www.youtube.com/watch?v=Iy-F7iSIopA
- Killed_by_Death
- New member
- Posts: 7
- Joined: Tue May 17, 2016 9:52 am
bridge height raises action
The higher the bridge floats, the higher your action is going to be.
There will come a point where the bridge is too high, and the saddles bottom out before you get your action where you want it.
There will come a point where the bridge is too high, and the saddles bottom out before you get your action where you want it.
"The pleasure is to play, makes no difference what you say."
Ian Fraser Kilmister (24 Dec 1945 – 28 Dec 2015)
Ian Fraser Kilmister (24 Dec 1945 – 28 Dec 2015)
Re: Tremolo Arm Setup
As Brad said, there are lots of interrelated variables to consider. If the action gets too high, you could shim the neck angle to lower the action and raise the pickups to get them back where you want them in relation to the strings. You still have keep in mind that the more you set the vibrato for pulling the strings sharp, the less it will go in the down direction. It is easy to bend a string up, not so easy to bend them flat.Folkie wrote: Isn't it the case that the higher the bridge, the more you can raise the pitch with the tremolo arm?
https://www.youtube.com/watch?v=Iy-F7iSIopA
I should experiment a bit with the vibrato on my PRS but there is only so far I can go on that as it won't take to shimming the neck very well..............
- Killed_by_Death
- New member
- Posts: 7
- Joined: Tue May 17, 2016 9:52 am
Re: Tremolo Arm Setup
Ah-Ha, so now we know at least one advantage to a bolt-on neck.
"The pleasure is to play, makes no difference what you say."
Ian Fraser Kilmister (24 Dec 1945 – 28 Dec 2015)
Ian Fraser Kilmister (24 Dec 1945 – 28 Dec 2015)
Re: bridge height raises action
Thanks for the insights. Right now the action on the guitar is low and comfortable, and I do a lot of down-bends, so maybe I should leave it as is. On the other hand, I have played a few Floyd Rose-equipped guitars with very high floating bridges and extremely low action. I'd only like to shim the neck as a last resort.
Re: Tremolo Arm Setup
The Floyd Rose vibrato is a totally different animal to the Strat vibrato, and the way it is installed allows for pulling up to a much higher degree..
Re: Tremolo Arm Setup
I have another question about the whammy bar on my new Strat. It currently dangles loosely near the volume and tone controls, making it an inconvenience to grab with my palm or fingers. Without over-tightening, is there a way to get it tight enough to rest parallel to the neck (ala Jeff Beck) for easier access? (When I try to tighten it, the bar will not make a full revolution without over-tightening.) I hope my question is clear. Any advice?
Re: Tremolo Arm Setup
Come over and try the PRS I have for sale.
- Badanovski
- Member
- Posts: 246
- Joined: Sat Oct 01, 2011 7:19 pm
Re: Tremolo Arm Setup
Fender sells little black springs that you install in the hole you screw the arm in. These allow you to get just the amount of resistance on the arm swing you'd like.
Re: Tremolo Arm Setup
Different tremolo mechanism, no?jps wrote:Come over and try the PRS I have for sale.
Re: Tremolo Arm Setup
Would any of the chain stores carry or order these?Badanovski wrote:Fender sells little black springs that you install in the hole you screw the arm in. These allow you to get just the amount of resistance on the arm swing you'd like.
Re: Tremolo Arm Setup
Thanks, Rock! Found those springs at Sam Ash.