Toaster covers on HiGains W/ adj. pole pieces

Building pickups from the ground up

Moderator: jingle_jangle

User avatar
ric330
Intermediate Member
Posts: 752
Joined: Fri Aug 11, 2006 3:58 pm

Toaster covers on HiGains W/ adj. pole pieces

Post by ric330 »

For newer Higains with threaded pole pieces this can be acheived quite easily.
All you'll need is a few tools:
regular #2 Phillips, a #1 Phillips, a couple Allen head wrenches (3/32) one straight, one "L" shape for tight pole pieces,
and a fine tip flat head to put the modified pole piece back in.

Image

Take your pickguard off and remove pickups. Remove pickup rings. No need to unsolder the PU's from the wiring harness.
You just want to remove the pole pieces with a 3/32 Allen head wrench:

Image

After removing a set of pole pieces, go to a bench vise and clamp the head of the screw right near
the end of the vise and cut head off with hack saw. Cut right at the head and don't miss up your pole piece threads.
The pole pieces are quite hard but will cut fast with a sharp hack saw. Like this:

Image

I used a bench grinder for a second to smooth the cut before proceeding. Now I clamped the threads of the headless pole piece between 2 hard plastic doners
(My Mustang spark wire organizer clips) in the vise to protect the threads and cut straight down the center of my original cut about a 1/16th of and inch, so I can
use a fine 1/8" screw driver to screw pole piece back in the bobbin from below instead of from above.

Image

Now the pole piece looks like this:

Image

Now I'm screwing in the pole piece from below (NOTE these are adjustable now from below the pickup, to balance your string to string relationship for the given PU)
Pretty cool - And it works. I did several tests to verify this. If say your bass string, on your Neck pickup is too strong then just remove the pickup and unscrew the pole
piece a bit for that given string. I started with all pole pieces up flush to the Toaster cover and then dropped down pole pieces as necesary. Since the original pole piece tops
were above the original HiGain chrome frame you simply raise your modified Toaster top HiGain PU closer to the strings until you find your sweet spot then adjust from below to suit. After you've gone through this process - it's a set and forget deal. But you can always adjust at some later time.
Install pole pieces from the back now and install Toaster top cover:

Image

Heres the neck pickup done:

Image

So I did the bridge pickup and put her back together. Since I just finished a Vintage Tuner conversion from stock Schallers the guitar looks really vintage now.
I get the HiGain and ability to not only adjust height of pickup but adjust the pole pieces to suit the response of the individual strings. BUT I get the vintage look 8)
What's it sound like? Awesome, just like before - which I was entirely happy with. Me buddy couldn't tell the difference. It certainly still sounds like a HiGain.

I think it was well worth it for me. I enjoyed the project and hope you guys got a kick out of it. I'm back and forth on the vintage knobs as I haven't really
found this particular model with the vintage knobs on them. They all seem to have the chrome top knobs since it's redesign of the rounded top body of 1964.

So here it is - a pretty much correct in appearance vintage 360 in JG ( actually a modded 07 360 JG)

Image
...went in to buy a 52' Tele and walked out with a 360 Jetglo...
User avatar
godber
Advanced Member
Posts: 2650
Joined: Fri Sep 16, 2005 11:07 am

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by godber »

Great thread again Kevin, I really like this kind of thing - and a list of tools as well !!!.

The 360 looks superb, really nice job.
User avatar
scotty
Senior Member
Posts: 7096
Joined: Thu Nov 22, 2007 11:27 am

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by scotty »

Yeah brilliant thread Kevin I really enjoyed this. Your 360 looks gr8. :mrgreen:
User avatar
steverok
Intermediate Member
Posts: 1137
Joined: Mon Mar 14, 2005 7:16 pm
Contact:

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by steverok »

Sweet. Nothing beats a 360JG, and yours is now a cut above !
User avatar
ric330
Intermediate Member
Posts: 752
Joined: Fri Aug 11, 2006 3:58 pm

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by ric330 »

I really like it now because it has the look I want but still is the same guitar I bought it the first place.
Nothing lost but vintage look gained. The vintage case should be here soon and I just got m y Rickenbacker Black strap.
I'm still anxiously waiting for my T shirt and Calender.
...went in to buy a 52' Tele and walked out with a 360 Jetglo...
User avatar
ajish4
RRF Moderator
Posts: 8566
Joined: Sat Oct 15, 2005 6:00 am

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by ajish4 »

Kevin,

THANK YOU for posting such a cool STEP BY STEP thread.

I printed it up for future reference.

Do you know if this would this work on a BASS High Gain, being it only has 4 lugs?

I'd love to convert the HG on my FL!
User avatar
ric330
Intermediate Member
Posts: 752
Joined: Fri Aug 11, 2006 3:58 pm

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by ric330 »

There is a post about that in the Rickenbackers Wanted section. "Allen Screws w/o mushroom heads for the newest Higains?"

If the polepieces aren't threaded you can drive them out carefully with a center punch and a grooved piece of wood. Then cut the heads off and drive them back in.
This method requires you to take out the pickup from the wiring harness so you are able to work on them.

Otherwise if the pole pieces have an Allen head mushroon type head you can just screw them out and replace with allen head studs or
use your originals doing the steps above. Cut head off, cut slot in the headless polepiece and screw them back in.
...went in to buy a 52' Tele and walked out with a 360 Jetglo...
User avatar
Ricmanx1
New member
Posts: 21
Joined: Sun Dec 09, 2007 5:40 pm

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by Ricmanx1 »

Great thread Kevin, I've been meaning to do this to my 330AFG,where did you get your toaster covers from?...
User avatar
ric330
Intermediate Member
Posts: 752
Joined: Fri Aug 11, 2006 3:58 pm

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by ric330 »

Hello Robert,
Teb told me to call Mike Parks at The Rickenbacker Page:

http://www.the-music-connection.com/ricpart.htm

Scroll down to Guitar Pickups 4th item down:
Part # 02086

I pretty sure he has them in stock.
...went in to buy a 52' Tele and walked out with a 360 Jetglo...
User avatar
Ricmanx1
New member
Posts: 21
Joined: Sun Dec 09, 2007 5:40 pm

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by Ricmanx1 »

Kevin, Thanks for the link........
User avatar
goofyfoot
Intermediate Member
Posts: 976
Joined: Sun Sep 30, 2007 8:31 am

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by goofyfoot »

Ric330.....Schoolteachers are students at heart. I thoroughly enjoyed being the student in your thread. Fascinating! Great setup and easy-to-follow procedures enhanced efficacy (ability to produce the desired result). Thanks for sharing, "Sensei" (Japanese for "teacher"). This is solid enough to be bookmarked. Best regards....Goofyfoot.
Play on, pick often, jam with any Rickenbacker, and prosper.
User avatar
ric330
Intermediate Member
Posts: 752
Joined: Fri Aug 11, 2006 3:58 pm

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by ric330 »

Thanks, I thought it may be useful since I acheived the desired results.
I did think about using some allen head studs in place of original polepieces but wanted to retain as much of the original pickup as possible.
It worked out great and was easier than expected.
...went in to buy a 52' Tele and walked out with a 360 Jetglo...
User avatar
admin
Site Admin
Posts: 15029
Joined: Wed Jul 05, 2000 5:00 am
Contact:

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by admin »

This pickup modification is interesting to me for two reasons. To begin, it allows for that traditional look with the edgy high gain sound. Moreover, it is also a comment that the high gain pickups are preferred by many on their Rickenbacker guitars.

For me, the modification allows for a uniform look while mixing toasters and high gains. My 350 Liverpool sounds best to me with hot toasters in the bridge and middle and a high gain at the neck. Others will prefer just the opposite. With my 24 fret model, the toaster at the neck just does not do it for me, but the high gain works nicely.

I have tired all combinations of humbucking, high gain and toasters in my 350 and have finally settled on a TTH arrangement for the neck, middle and bridge, respectively. My favourite setting is the bridge and neck which has a sparkle like no other non-Rickenbacker that I have heard.
Life, as with music, often requires one to let go of the melody and listen to the rhythm

Please join the Official RickResource Forum Facebook Page https://www.facebook.com/groups/379271585440277
btomlinson
Junior Member
Posts: 105
Joined: Wed Feb 22, 2006 9:44 am

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by btomlinson »

What are the high pole pieces for if you can just cut them off. Why would Rick use them?

I love your work. What a great idea.

Thanks
btomlinson
Junior Member
Posts: 105
Joined: Wed Feb 22, 2006 9:44 am

Re: Toaster covers on HiGains W/ adj. pole pieces

Post by btomlinson »

Now if I could only change the headstock to the older smaller version.

Great stuff.
Post Reply

Return to “Winding Up With The Best: by Sergio Silva”