1937 - 38 Lap Steel Pickup Replacement?
Moderators: rickenbrother, ajish4
-
- New member
- Posts: 5
- Joined: Sun Aug 12, 2012 4:35 am
1937 - 38 Lap Steel Pickup Replacement?
I'm having a horrible time finding a replacement pickup that will fit into the horse shoe assembly on this rebuild I am doing. Do we know of any pickups that will work? Without needing to buy the entire horseshoe assembly? I can send this to have the Bobbin repaired and have the pickup rewound but I figured I should check here first because you fellas know more than me by default.
Thank you so much for this community, and thanks in advance for any advice.
Thank you so much for this community, and thanks in advance for any advice.
-
- New member
- Posts: 5
- Joined: Sun Aug 12, 2012 4:35 am
Re: 1937 - 38 Lap Steel Pickup Replacement?
I wanted to post a picture of the P/U I'm sure you fellas have seen these before, but this is what I'm looking to replace.
Re: 1937 - 38 Lap Steel Pickup Replacement?
I would just rewind the bobbin and pit some magnets beneath it, then mount it on a piece of aluminum bar stock with screw holes to fit beneath the assembly.
Great Ramp In My Opinion.
-
- New member
- Posts: 5
- Joined: Sun Aug 12, 2012 4:35 am
Re: 1937 - 38 Lap Steel Pickup Replacement?
I still have the horseshoe magnets and all the assembly.
-
- New member
- Posts: 18
- Joined: Sun Aug 15, 2010 10:43 pm
Re: 1937 - 38 Lap Steel Pickup Replacement?
Yes you can have the bobbin rewound, then reassemble everything. You might also want to consider having the horseshoes remagnatized while It's apart.
Ron
Ron
-
- New member
- Posts: 5
- Joined: Sun Aug 12, 2012 4:35 am
Re: 1937 - 38 Lap Steel Pickup Replacement?
Is there anyway to magnetize them myself?
- 8mileshigher
- Senior Member
- Posts: 4871
- Joined: Tue May 23, 2006 12:34 pm
1937 - 38 Lap Steel Pickup Replacement?
Rickenbummer wrote:Is there anyway to magnetize them myself?
There are several threads here on the RRF about re-magnetizing or re-charging Horseshoes. Do some searches on these Horseshoe topics and re-magnetizing or other similar words. There are also some talented people on the RRF, who know a lot about electronics and pickups, (like John A and CJJ and others) who might be able to assist you in getting these Horsies functioning again. Good luck.
-
- New member
- Posts: 5
- Joined: Sun Aug 12, 2012 4:35 am
Re: 1937 - 38 Lap Steel Pickup Replacement?
I found them after I asked, sorry about that, so I'm screwed, the guy I sent the pickup to for repair/rewinding simply broke it... I won't get into it because I'm tired of being mad about it. Is there no bolt on pickup replacement that can be attached to the metal plate inside the mags? I have the entire assembly, only the bobbin is broken, is there no replacement?
Re: 1937 - 38 Lap Steel Pickup Replacement?
Too bad this wasn't posted a bit sooner ... IIRC, there was an ad on the Portland (OR) Craigslist a couple of weeks ago for some old lap steel horseshoe pickups.
Unfortunately, the ad has expired (and apparently has not been reposted).
Unfortunately, the ad has expired (and apparently has not been reposted).
It is better, of course, to know useless things than to know nothing. - Seneca
Re: 1937 - 38 Lap Steel Pickup Replacement?
Since your coil has 6 poles, you could get a toaster, pull the magnets out, put in steel screws, then reassemble the horseshoe assemble. Use the magnet assembly of an old woofer to recharge the shoes.