German Carve
Moderator: jingle_jangle
Re: German Carve
That’s the one! Better work... but if Fralin rewound it then it should be great & will be wax potted too. I’ll clean up the patina enough that I don’t get tetanus but I’m looking for that ancient bell tone. Can’t go back further than 30’s and when would I find another that old? The inch 1/2 is better from a tonal standpoint although a 50’s/60’s 1 1/4 would have been simpler & was what I was expecting to eventually find. Step one will be to wire it up in my dormant Electro & wake it up. Then figure out how to mount it...maybe hog out under the top so I can attach it with no surround?
Sanding...
Sanding...
Sanding...
Sanding...
Sanding...
Sanding...
Re: German Carve
Dom wrote:... I’ll clean up the patina enough that I don’t get tetanus ...
Re: German Carve
Hand-carving into a 350 body sounds like quite the undertaking! (and it would definitely need to be shallow since the body is thinner than you might expect, the Polynesian might have started as a thicker body to allow for the German carve).
Post some pics though! Would love to check out your progress. The carve is one of the nicest features of the handmade Rossmeisl guitars, in my opinion. Gorgeous.
Post some pics though! Would love to check out your progress. The carve is one of the nicest features of the handmade Rossmeisl guitars, in my opinion. Gorgeous.
Re: German Carve
Hi Collin! I came to my senses on carving the 350 & continued with what was a 3/4 Washburn Idol *pinecaster. The carve really needs the extra depth to look “right” & there’s no room for error. Besides the 850 carve is really what I want to replicate. I’m trying to do everything on the carve by hand. Roger would have had jigs to make things faster but I’m really getting a feel for the process.
The gooseneck scraper does the rough out, sanding dowel evens up any grain inconsistencies, re-burred scraper does the final pass. I’m doing some work using small files especially where the carve ends above the pickguard point.
*I’m getting video of the build from here on out...constant interruptions & all Since it won’t be a Ric I’ll do a build page where appropriate.
The gooseneck scraper does the rough out, sanding dowel evens up any grain inconsistencies, re-burred scraper does the final pass. I’m doing some work using small files especially where the carve ends above the pickguard point.
*I’m getting video of the build from here on out...constant interruptions & all Since it won’t be a Ric I’ll do a build page where appropriate.
Re: German Carve
https://imgur.com/gallery/09jjqjN
https://imgur.com/gallery/o8cuBya
Here’s a link with my latest progress. I still don’t know how to post directly from Imgur...cheers!
https://imgur.com/gallery/o8cuBya
Here’s a link with my latest progress. I still don’t know how to post directly from Imgur...cheers!
Re: German Carve
https://imgur.com/gallery/rTVXanO
The carve is nearly complete! I routed the edge down 1/4” and this allowed me to even up the carve using sanding dowels in 80 and 150 grit. The facet by the controls was left rough until this last stage so the radius & final depth could first be established. This section was then done by hand with a small file. The most difficult part has been the treble horn and getting the compound curves correct. Very minute divots due to the different densities in the grain required hours to even out. Hours. Pine wants to do whatever the grain says but diligence paid off. Maple on the other hand behaves consistently & I bet this job would have gone much quicker over pine. Check the pics to see.
Yes, a separate build thead will be happening in Forum 51. Cheers!
The carve is nearly complete! I routed the edge down 1/4” and this allowed me to even up the carve using sanding dowels in 80 and 150 grit. The facet by the controls was left rough until this last stage so the radius & final depth could first be established. This section was then done by hand with a small file. The most difficult part has been the treble horn and getting the compound curves correct. Very minute divots due to the different densities in the grain required hours to even out. Hours. Pine wants to do whatever the grain says but diligence paid off. Maple on the other hand behaves consistently & I bet this job would have gone much quicker over pine. Check the pics to see.
Yes, a separate build thead will be happening in Forum 51. Cheers!
Re: German Carve
Awesome work!
"Hours" is right!
"Hours" is right!
Re: German Carve
Dom,
Very, very cool!
Len
Very, very cool!
Len
Re: German Carve
Thanks Len! It is too bad all that work didn’t translate to a decent guitar. It was a good way to figure out how to do the carve but the wood was too cheap. The other body I’d used for the 600 style was decent and this one was like the shop floor and glue. It’s going to be a wall hanging. It took a whomp in a moving van…so then the shoe was going to go to the 350…then the house flooded & got fixed…then pandemic…no music…started restoring muscle bicycles and learned how to do kandy paint jobs & fades…music popped back up and now my brood has had all their shots. No more excuses. Time to grab the horseshoe pickup and get that 350 going!