BT Tailpiece?
Posted: Tue Apr 18, 2006 5:42 pm
Does anyone have a spare BT tailpiece to sell? I am looking for a one for my Blackstar. The original has developed quite a bit of lift and must be replaced.
Rickresource Rickenbacker Forum
Rickenbacker Forum, Amplifier, Bass and Guitar Register
https://www.rickresource.com/forum/
BT Tailpiece?
Page 1 of 1
Posted: Tue Apr 18, 2006 11:42 pm
Hey Ted, my e-mail messages keep failing to reach you. What could be the problem?
Posted: Wed Apr 19, 2006 3:05 am
Doesn't a Blackstar have the two extra screws in the back?
I'd have a chrome one bead blasted and powder coated if you can't find a black one.
I'd have a chrome one bead blasted and powder coated if you can't find a black one.
Posted: Wed Apr 19, 2006 3:19 am
I would add 2 extra screws ...
Posted: Wed Apr 19, 2006 4:26 am
Some Blackstars may have the extra screws but mine does not. My Tux does.
I thought of adding screws but it is bent so much that the sides are distorted.
I thought of adding screws but it is bent so much that the sides are distorted.
Posted: Wed Apr 19, 2006 4:28 am
Sergio: I will check our spam filters. We have been getting spam-blasted by drone machines all over Portugal and France for the past month or so.
Posted: Wed Apr 19, 2006 11:50 pm
Ted, could you post a picture of the bent tailpiece? I find it difficult to believe that it is worse off than the one on my 4003S/5 SPC which I was able to bring back to functionality.
BTW, I pulled out my Blackstar (the 'real' one) tonight and noticed that the tailpiece is showing some lift, so I will need to work on it like I did the five-string, namely rebend, drill holes, and install screws.
BTW, I pulled out my Blackstar (the 'real' one) tonight and noticed that the tailpiece is showing some lift, so I will need to work on it like I did the five-string, namely rebend, drill holes, and install screws.
Posted: Fri Apr 21, 2006 8:27 am
I have a 4-hole BT tail piece I'm willing to sell.
Posted: Fri Apr 21, 2006 9:00 am
You could hold on to the original and just buy a black Hipshot replacement. They're direct replacements, so no modification is necessary, and then you'll still have the original to keep it stock.
Posted: Fri Apr 21, 2006 9:12 am
Ted, I'll show you my black Hipshot tomorrow.
Posted: Fri Apr 21, 2006 10:14 am
Posted: Fri Apr 21, 2006 11:52 am
Alan, I hope you don't mind:
I'd say that it's a viable alternative; good suggestion, guys!
I'd say that it's a viable alternative; good suggestion, guys!
Posted: Fri Apr 21, 2006 11:55 am
That photo was pre-intonation, obviously...
The only issue I have with this design is that the screws do not thread all the way through the saddles. As a result the intonation adjustment with the included long screws may not be enough. In that case you can 1) email the guys at Hipshot and ask for some shorter screws or b) go get them yourself; they are a standard thread and diameter.
The only issue I have with this design is that the screws do not thread all the way through the saddles. As a result the intonation adjustment with the included long screws may not be enough. In that case you can 1) email the guys at Hipshot and ask for some shorter screws or b) go get them yourself; they are a standard thread and diameter.
Posted: Fri Apr 21, 2006 12:00 pm
I might use a Hipshot on some of my other Ricks but the Blackstar and the other limited edition instruments are going to stay as stock as possible.
Posted: Fri Apr 21, 2006 7:44 pm
Ted, how about a picture of the bad tailpiece?