Ric Finish

Vintage, Modern, V & C Series, Signature & Special Editions

Moderators: rickenbrother, ajish4

Post Reply
bill_yantz
Member
Posts: 275
Joined: Sat Jun 05, 2004 5:00 am

Ric Finish

Post by bill_yantz »

What year did Ric start using conversion varnish for the final finish? What did they use prior to that?
A British Invasion Tribute
http://www.myspace.com/billyyantz
bill_yantz
Member
Posts: 275
Joined: Sat Jun 05, 2004 5:00 am

Post by bill_yantz »

Ping - this has got to be an easy one for Team-Ric.
A British Invasion Tribute
http://www.myspace.com/billyyantz
bill_yantz
Member
Posts: 275
Joined: Sat Jun 05, 2004 5:00 am

Post by bill_yantz »

Ping. This has got to be an easy one for Team-Ric.
A British Invasion Tribute
http://www.myspace.com/billyyantz
User avatar
johnhall
RIC
Posts: 3926
Joined: Tue Sep 26, 2000 11:17 am
Contact:

Post by johnhall »

1958 marked the change from nitrocelulose to conversion varnish. (Didn't I just say that in another thread somewhere?)
User avatar
jingle_jangle
RRF Moderator
Posts: 22679
Joined: Wed Dec 22, 2004 6:00 am
Contact:

Post by jingle_jangle »

Ping. Is there an echo in here? Perhaps two?
“I say in speeches that a plausible mission of artists is to make people appreciate being alive at least a little bit. I am then asked if I know of any artists who pulled that off. I reply, 'The Beatles did.”
― Kurt Vonnegut
bill_yantz
Member
Posts: 275
Joined: Sat Jun 05, 2004 5:00 am

Post by bill_yantz »

Thanks John.

Paul, operator error, as usual.

I will admit, I am a little confused with exactly what conversion varnish is. I will search the archives to refresh.

Would you give me a tip on a small repair. I want to repair two side-by-side nicks on the end of the upper bout slightly to the bottom right of the strap button (Fireglo, late 360). One nick has a small dot of wood showing. Can I fill it and sand to blend and if so what should I use.

Thanks as always.
A British Invasion Tribute
http://www.myspace.com/billyyantz
User avatar
jingle_jangle
RRF Moderator
Posts: 22679
Joined: Wed Dec 22, 2004 6:00 am
Contact:

Post by jingle_jangle »

Fireglo...A tough one. You can fill and level the varnish easily, but touching up the FG will prove to be nigh impossible if it's nicked through to the wood.
“I say in speeches that a plausible mission of artists is to make people appreciate being alive at least a little bit. I am then asked if I know of any artists who pulled that off. I reply, 'The Beatles did.”
― Kurt Vonnegut
gjg59
Veteran RRF member
Posts: 93
Joined: Thu Oct 24, 2002 4:47 am

Post by gjg59 »

Mine was certainley not a professinal repair but it worked for me. I had a nasty nick on the bottom of my 95 Fireglow 330. It was down to the bare wood on the lower bout of the guitar on an edge. I matched the color very well going thru my kid's crayon collection. I colored in the nick. I them flowed polyurethane into the are using small drops off a matchstick, drying in between. It gotta was almost undetectable after that.
User avatar
tony_carey
Advanced Member
Posts: 2055
Joined: Thu Oct 28, 2004 6:00 am
Contact:

Post by tony_carey »

It's amazing what you can do with crayons. Nail polish is great for touching up gtrs too & it smells better than crayons!
'Rickenbacker'...what a name! After all these years, it still thrills me.
Post Reply

Return to “Rickenbacker Guitars: by John Simmons”