370/360 wireing
Moderator: jingle_jangle
-
- New member
- Posts: 50
- Joined: Fri Oct 02, 2009 10:46 am
370/360 wireing
Can someone draw the wireing diagram for this model? the picture of Chris's 370 is great but I cant make out which wire goes where..but if someone could draw it out and post it,,that would be cool..I have the stereo hookups on this 370/12 thanks in advance............
- 8mileshigher
- Senior Member
- Posts: 4871
- Joined: Tue May 23, 2006 12:34 pm
Re: 370/360 wiring
Did you check this thread viewtopic.php?f=13&t=396148&start=0
There are also Schematics at the Ric company website:
http://www.rickenbacker.com/pdfs/19514.pdf
Hope its of some help.
There are also Schematics at the Ric company website:
http://www.rickenbacker.com/pdfs/19514.pdf
Hope its of some help.
-
- New member
- Posts: 50
- Joined: Fri Oct 02, 2009 10:46 am
Re: 370/360 wireing
Thanks for reply..I looked at that wireing diagram,,,I see where the pickups hook up..but I dont see where the mono/stereo jacks hookup to the pots..my wireing harness that I got from Ric. for the RCA jacks have 3 wires..one grey wire with 2 wires in it,one ground and one hot wire..the other wire has one wire in it..so I looked at the Ric schmatic and I cant make heads or tells of where to hook these wires for the mono/stereo jacks..so if someone can draw the set up that would be great..thanks again Larry
- 8mileshigher
- Senior Member
- Posts: 4871
- Joined: Tue May 23, 2006 12:34 pm
Re: 370/360 wiring
Maybe some of the more knowledgeable "electrics guys" on the Forum might be able to chime in and help you...
Paging JohnAllg or Beatlefreak ?
Paging JohnAllg or Beatlefreak ?
Re: 370/360 wireing
Lawrence, see if this pic of a bass controls helps:
-
- New member
- Posts: 50
- Joined: Fri Oct 02, 2009 10:46 am
Re: 370/360 wireing
Thanks John,,,this is a Bass control? does it have the ROS 2 RCA jacks? and is this just like the 360/370 hookups/ thanks again Larry.....I no Beatlefreak has a 360 with ROS...help my freind
Re: 370/360 wireing
Yes, a bass, 4 control, two pickups. Yes it has ROS. The jack with the two long shielded wires is the mono one. The wire with the shield lead goes to the treble volume pot like in the schematic. The other wire without the shield wire showing goes to the bass volume pot like in the schematic. Consult the pic I posted and the linked schematic to figure where to solder.BeatlesGuy wrote:Thanks John,,,this is a Bass control? does it have the ROS 2 RCA jacks? and is this just like the 360/370 hookups/ thanks again Larry.....I no Beatlefreak has a 360 with ROS...help my freind
- analogpackrat
- Member
- Posts: 496
- Joined: Tue Jul 24, 2007 5:34 am
Re: 370/360 wireing
Here's a pic of my '72 360 S/12:
Standard wiring. I think the original owner swapped in the orange drops before I bought it, but nothing else has been changed as far as I can tell.
Here's the original naked pick guard from my '64 375. You can't see it, but the 0.0047uF series bridge PU cap is under one of the tone caps.
Standard wiring. I think the original owner swapped in the orange drops before I bought it, but nothing else has been changed as far as I can tell.
Here's the original naked pick guard from my '64 375. You can't see it, but the 0.0047uF series bridge PU cap is under one of the tone caps.
If it is to be, it is up to me.
-
- New member
- Posts: 50
- Joined: Fri Oct 02, 2009 10:46 am
Re: 370/360 wireing
thanks a tone,,I think I have a bad/dead pup I have a 370 and have no sound at the bridge pup...it new from pick of the rick, so I'll have to wait until he reopens the first of August...damn...tape on it and nothing..any suggestions?
- analogpackrat
- Member
- Posts: 496
- Joined: Tue Jul 24, 2007 5:34 am
Re: 370/360 wireing
Can you post a pic of your wiring? Do you have a ohm-meter of some sort (any cheap DMM will do)? If so, you can check for gross things like the pickup being open or short.
Also, what exactly are you doing or fixing on the guitar and what worked or didn't work before hand?
Also, what exactly are you doing or fixing on the guitar and what worked or didn't work before hand?
If it is to be, it is up to me.