Polishing Mystery

Exceptional restoration is in the details

Moderator: jingle_jangle

Post Reply
User avatar
deaconblues
RRF Consultant
Posts: 2390
Joined: Tue Feb 06, 2007 5:14 pm

Polishing Mystery

Post by deaconblues »

Hey there Paul,

I finally got around to giving my 325 its first good Scratch-X/Zymol treatment last night, and the finish has never looked so shiny and deep. However, I noticed afterward that my cloths were covered in black smudges. Would it be possible for some of the finish to come off during polishing, or is that just dirt? Anything to worry about? Thanks.
User avatar
jingle_jangle
RRF Moderator
Posts: 22679
Joined: Wed Dec 22, 2004 6:00 am
Contact:

Re: Polishing Mystery

Post by jingle_jangle »

Dan, It's very unlikely that you've got paint on the cloths. Much more likely that it's from the frets or simply dirt.
User avatar
deaconblues
RRF Consultant
Posts: 2390
Joined: Tue Feb 06, 2007 5:14 pm

Re: Polishing Mystery

Post by deaconblues »

Thanks, Paul. I figured it was unlikely to be the finish, but I wasn't 100%. It sure looked like it, though!
User avatar
jingle_jangle
RRF Moderator
Posts: 22679
Joined: Wed Dec 22, 2004 6:00 am
Contact:

Re: Polishing Mystery

Post by jingle_jangle »

JG is a very thin finish, the CV is 10X thicker in most places. The factory doesn't buff through the CV. Scratch-X is a very mild abrasive, though I suppose that with a lot of pressure on edges, where paint and CV is thinnest, it could cut through the CV into the JG color coat. Anyway, should you in subsequent polishings, cut into bare maple, it would be time for a CV touch-up.

To check this, you can put a bit of Scratch-X on a soft cotton cloth and work it into the weave. now, stroke along the suspect edge area, rubbing lightly. If you see the smudges (and they'll be streaks, since you're rubbing along the edge!), then stop. You've rubbed through in that area. 99% of the time, it's edges that rub through.

If you don't get smudges, it was something else staining the cloth. In Aitch's case, it would be chicken grease.

This method can be used for any color, not just CV.

Fix for rub-throughs is nothing less than a CV touchup. In the case of JG, best to re-CV the whole instrument.
User avatar
kiramdear
RRF Moderator
Posts: 9045
Joined: Fri Jun 27, 2008 2:51 am
Contact:

Re: Polishing Mystery

Post by kiramdear »

jingle_jangle wrote:
If you don't get smudges, it was something else staining the cloth. In Aitch's case, it would be chicken grease.

:lol: :lol: :lol: :lol: :mrgreen:
All I wanna do is rock!
User avatar
johnallg
Rick-a-holic
Posts: 17688
Joined: Wed Apr 05, 2006 12:13 pm

Re: Polishing Mystery

Post by johnallg »

Fretboards are usually dirtier then you realize... :lol:
User avatar
ozover50
RRF Consultant
Posts: 10492
Joined: Mon Jan 17, 2005 1:07 pm
Contact:

Re: Polishing Mystery

Post by ozover50 »

If you don't get smudges, it was something else staining the cloth. In Aitch's case, it would be chicken grease.
Haven't had roast chicken within 30 feet of any of my Ricks since that episode, Paul!! :wink:
"Never eat more than you can lift." - Mr. Moon
User avatar
winston
Membership Admin
Posts: 11010
Joined: Mon Jul 11, 2005 5:00 am

Re: Polishing Mystery

Post by winston »

ozover50 wrote:
If you don't get smudges, it was something else staining the cloth. In Aitch's case, it would be chicken grease.
Haven't had roast chicken within 30 feet of any of my Ricks since that episode, Paul!! :wink:
Oh this sounds like a great story Aitch................ :lol:
“We can't solve problems by using the same kind of thinking we used when we created them.” - Albert Einstein

"You do not really understand something unless you can explain it to your grandmother" - Albert Einstein
User avatar
beatlefreak
Senior Member
Posts: 6160
Joined: Wed Jun 14, 2006 5:45 am
Contact:

Re: Polishing Mystery

Post by beatlefreak »

Yes, do tell!
Ka is a wheel.
Post Reply

Return to “Reflections of a Curmudgeon: by Paul Wilczynski”